-
Product Center
-
-
-
Unmanaged Industrial Switches(Extended Temp)
Unmanaged Industrial Switch
L2 Managed Industrial Switches
L3 Managed Industrial Switches
TSN Industrial Switch
Managed Industrial PoE Switch
M12 Industrial Switch
Industrial 100-Mbps Transceiver
Industrial Gigabit Transceiver
Unmanaged Switch
L2 Managed Switches
Standard PoE Switches
Non-standard PoE Switches
Managed PoE Switch
Unmanaged Domestic Switches
Managed Domestic Switches
Unmanaged Waterproof Switches
Managed Waterproof Switches
100M Fiber Optic Transceivers
Gigabit Fiber Optic Transceivers
Fiber Optic Transceiver Chassis
Pure Telephone Optical Terminals
Telephone&Ethernet Optical Terminals
Integrated Service Telephone Optical Terminals
HDMI Video Optical Terminals
SDI Video Optical Terminals
VGA Video Optical Terminals
DVI Video Optical Terminals
3.5mm Interface Audio Optical Terminals
RCA Interface Audio Optical Terminals
XLR Interface Audio Optical Terminals
Commercial-grade Dry Contact Optical Terminals
Industrial-grade Dry Contact Optical Terminals
RS485 Date Optical Terminals
E1 Over IP
Voier Over IP
Pure E1 Optical Terminals
1+1 Fiber Back-up Optical Terminals
4~30 Channels PCM Multiplexers
Ethenet Over 1~16*E1 Converters
1~32 Serial Port Servers
Industrial 4G Routers
Industrial 5G Routers
2.4G/5.8G Wireless Bridge
Wireless AC Controller
Gigabit Optical Modules
Power Adapter
Rail-Mounted Power Supply
Fiber Optic Pigtail
Terminal Box
GQ-DOT01A
1-way bidirectional RS-232 optical transceiver
Keywords
Commercial Switches
Domestic Switches
隐藏域元素占位
Category:
Commercial Switches
Domestic Switches
Product Overview
The RS232 optical transceiver converts bidirectional RS232 signals into optical signals for transmission over fiber optic cables. It supports SC, FC, and ST connectors and can operate with either single‑fiber or dual‑fiber interfaces. This RS232 optical transceiver addresses the limitations of conventional RS232—such as short transmission distances and poor immunity to interference—while also mitigating electromagnetic interference, ground‑loop noise, and risks from lightning strikes and voltage surges, thereby significantly enhancing the reliability, security, and confidentiality of data communications.
Serial optical transceivers are typically used in pairs, leveraging fiber optics to enable long-distance transmission of serial data. They are well-suited for network environments such as telecommunications equipment rooms, LED display communications, security surveillance, intelligent transportation systems, power monitoring, and environmental monitoring.
Product Features
1. Zero-delay automatic forwarding.
2. Supports a bidirectional RS-232 data interface.
3. Automatically detects the serial port baud rate and determines and controls the data transmission direction.
4. Serial port baud rate: 0–115,200 bps.
5. Operating wavelength: 850/1310 nm (multimode), 1310/1550 nm (single-mode).
6. The optical port supports FC, SC, and ST interfaces; multimode transmission ranges from 0 to 2 km, while single-mode transmission spans 0 to 120 km.
7. The status indicator lights are fully equipped, making the operating status immediately clear at a glance.
8. Built-in lightning protection circuitry significantly reduces damage caused by lightning-induced surges.
| Interface parameters | |
| Optical interface | Fiber optic mode: multimode and single-mode options available. Fiber Optic Connection: Single-fiber or dual-fiber options available. Physical interfaces: FC, SC, and ST are optional (FC is the default configuration at the factory). Fiber optic wavelengths: 850 nm, 1310 nm, 1550 nm Transmission distance: Multimode 0–2 km, Single-mode 0–120 km |
| Data Interface | Communication Standard: EIA RS-232 Standard Communication Data: RS-232 Communication rate: 0–115.2 kbps, adaptive Physical Interface: Industrial Terminal Block Data wiring: 3-wire configuration (RXD, TXD, GND), full-duplex, point-to-point communication. |
| Power Supply Characteristics | |
| Input voltage | DC5V |
| Full-load power consumption | <2W |
| Wiring Method | DC5525 power connector |
| Overload protection | Support |
| Work environment | |
| Operating temperature | 0–50°C |
| Storage temperature | -40～85℃ |
| Relative humidity | 5% to 95% (non-condensing) |
| Mechanical Properties | |
| Shell | Metal casing |
| Installation Method | Desktop-style |
| Warranty | |
| Warranty period | Two years |
Device model | Business Interface | Optical port | Power supply |
GQ-DOT01A-MDFC-2 | 1-way bidirectional RS232 data | 1 multimode dual-fiber F Type-C port | External power adapter |
GQ-DOT01A-SDFC-20 | 1-way bidirectional RS232 data | 1 single-mode dual-fiber F Type-C port | External power adapter |
GQ-DOT01A-SSFC-20 | 1-way bidirectional RS232 data | 1 single-mode single-fiber F Type-C port | External power adapter |
| When placing your order, please confirm whether the optical port is multimode or single-mode, whether it is single-fiber or dual-fiber, and the transmission distance in kilometers. FC, SC, and ST optical ports are available as options. | |||
Application Diagram: Fiber Optic Point-to-Point Networking
Related Documents
Name
Size
Type
Release Date
Download
Beijing–Tianjin–Hebei, Henan, Shanxi, Inner Mongolia, and Sichuan:+8613719208595
Fujian, Guangxi, Hainan, Yunnan, Guizhou, and Jiangxi:+863760887412
Heilongjiang, Jilin, Liaoning, Inner Mongolia, Hunan, Chongqing:18126729399
Jiangsu, Zhejiang, Shanghai, Shandong, and Anhui:+8618198851696
Shaanxi, Gansu, Ningxia, Qinghai, Xinjiang, and Tibet:+8618198851697
Guangdong Region:+8613302232639 +8618903052902
3rd Floor, Elevator No. 1, Building B, Guangzheng Science and Technology Park, No. 11, Nanyun Fifth Road, Huangpu District, Guangzhou City